Send SMS

Send SMS Enquiry

Thank you

Your Enquiry has been sent successfully.

+1
Send Email

Send Email

Thank you

Your Enquiry has been sent successfully.

+1

Products

Stainless Steel Products

Stainless Steel 301

Stainless Steel 301

Material : Use Of The Finest Grade Raw Material.

Stainless Steel 301 Coils Thickness Range : 0.025mm – 4.00mm

Stainless Steel 301 Coils Width : Soft, Half Hard, Half Hard, ¾ Hard, Full Hard & Spring Hard

Stainless Steel 301 Coils Hardness : Minimum 3.2mm to Maximum 2000mm

Stainless Steel 301 Coils Finish : 2b, 2d, Bright Annealed, #3 Polish, #4 Polish and More

Enquiry Now
Stainless Steel 304/304L

Stainless Steel 304/304L

304 is available in Sheet, Strip, Plate, Tube, Bar (Round), Rod, Rings, Forgings.Type 304 is a variation of the basic 18-8 grade, Type 304, with a higher chromium and lower carbon content. Lower carbon minimizes chromium carbide precipitation due to welding and its susceptibility to intergranular
Enquiry Now
Stainless Steel 309

Stainless Steel 309

Carbon (C) : 0.20 max%

Chromium (Cr) : 22.00 - 24.00%

Manganese (Mn) : 2.00 max%

Silicon (Si) : 0.75 max%

Phosphorous (P) : 0.45 max%

Enquiry Now
Stainless Steel 310

Stainless Steel 310

Stainless Steel 310 (AMS 5521 / AMS 5651) UNS S31000/S31008 Werkstoff 1.4842/1.4845:Alloy 310 is a austenitic chromium-nickel stainless steel. Alloy 310 is used where good corrosion and heat resistance are required. Alloy 310 has excellent oxidation resistance and can resist oxidation or scaling up
Enquiry Now
Stainless Steel 316 Ti

Stainless Steel 316 Ti

Carbon (C) : 0.03 max%

Chromium (Cr) : 16.00 - 18.00%

Manganese (Mn) : 2.00 max%

Silicon (Si) : 0.75 max%

Phosphorous (P) : 0.04 max%

Enquiry Now
Stainless Steel 316/316L

Stainless Steel 316/316L

Material : Alloy 316L, Alloy 316

Form : 316L Sheet AMS 5507, 316 Sheet AMS 5524

Tensile Strength (ksi) : 100 max, 75 min

Yield Strength (ksi) : 30

(%) Elongation : 45

Enquiry Now
Stainless Steel 321

Stainless Steel 321

Condition : Alloy 321 Tube

Tensile Strength Rm, N/mm² : 500-730

Yield Strength Rp 0.2, N/mm² : 200

Elongation % : 35

Enquiry Now
Stainless Steel 330

Stainless Steel 330

Material : Alloy 330 Annealed

Ultimate Tensile Strength (ksi) : 70

Yield Strength (ksi) 0.2 % : 25

Elongation in 2 : 30

Rockwell B Hardness : ≤95

Enquiry Now
Stainless Steel 347

Stainless Steel 347

Stainless Steel 347 (AMS 5512/AMS 5646) UNS S30347 Werkstoff 1.4544/1.4546/1.4550 :Alloy 347 is a chromium nickel stainless steel which has been modified by the addition of columbium and tantalum. The main advantage of this is an excellent resistance to intergranular corrosion which is common to
Enquiry Now
Stainless Steel 410

Stainless Steel 410

Stainless Steel 410 (AMS 5504) UNS S41000:Type 410 is a basic hardenable martensitic stainless steel and is well suited for use in highly stressed parts where properties such as corrosion resistance, good strength and ductility are required. 410 is used for steam / gas turbine blades and buckets,
Enquiry Now
Stainless Steel 420

Stainless Steel 420

Material ` : Alloy 420 Ann, Room Temp 1

Tensile Strength (Mpa) : 655

Proof Stress 0.2% (MPa) : 345

Elongation in 2 : 25

Reduction of Area % : 55

Enquiry Now
Stainless Steel 430

Stainless Steel 430

Material : Alloy 430 Annealed Sheet

Condition : Annealed (AMS 5503)

Tensile Strength (ksi) : 65

Proof Stress 0.2% (ksi) : 35

Elongation A5% : 20-22

Enquiry Now
Stainless Steel 431

Stainless Steel 431

Material : Steel

Application : Doors, Furniture, Grills, Gym

Color : Silver

Finishing : Polished

Features : Hard, Light Weight, Long Life, Stainless

Enquiry Now
Stainless Steel 440

Stainless Steel 440

Material : Stainless Steel

Shape : Rectangular, Square

Thickness : 100-200mm, 200-300mm, 400-500mm

Length : 1000-2000mm, 2000-3000mm, 3000-4000mm, 4000-5000mm

Application : Construction, Industry

Enquiry Now
Stainless Steel 904L

Stainless Steel 904L

Alloy : Alloy 904L Tube

Tensile Strength MPa : 500-700

Yield Strength (0.2% Offset) MPa : 200

Elongation (%) : 40

Grade : 904L

Enquiry Now

Nickel Alloy Products

Alloy 188

Alloy 188

At Harsh Steel Nickel 188 is available in Cobalt Alloy 188 wire, Cobalt Alloy 188 Round bar, Cobalt Alloy 188 Forged bar, Cobalt Alloy 188 hex bar, Cobalt Alloy 188 Flat bar, Cobalt Alloy 188 Circles, Cobalt Alloy 188 Ring, Cobalt Alloy 188 Tube, Cobalt Alloy 188 seamless Pipe, Cobalt Alloy 188
Enquiry Now
Alloy 230

Alloy 230

Alloy 230 is a nickel-chromium-tungsten-molybdenum alloy that combines excellent high temperature strength, outstanding resistance to nitriding environments and excellent long term thermal stability. Haynes 230 is easily fabricated and has very good forming and welding characteristics. Due to
Enquiry Now
Alloy A286

Alloy A286

Thickness of Alloy A286 Bars : 3mm Up to 600mm

Length of Alloy A286 Bars : 2mm to 6000mm

Tolerance of Alloy A286 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.08 max%

Manganese (Mn) : 2.00 max%

Enquiry Now
Alloy N-155

Alloy N-155

Multimet N155 is available in Multimet N155 wire, Multimet N155 Round bar, Multimet N155 Forged bar, Multimet N155 hex bar, Multimet N155 Flat bar, Multimet N155 Circles, Multimet N155 Ring, Multimet N155 Tube, Multimet N155 seamless Pipe, Multimet N155 Welded / ERW Pipe, Multimet N155 Sheet,
Enquiry Now
Custom 455

Custom 455

Thickness of Custom Alloy 455 Bars : 3mm Up to 600mm

Length of Custom Alloy 455 Bars : 2mm to 6000mm

Tolerance of Custom Alloy 455 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.05 max%

Manganese (Mn) : 0.50 max%

Enquiry Now
Hastelloy 276

Hastelloy 276

Thickness of Hastelloy Alloy C276 Bars- : 3mm Up to 600mm

Length of Hastelloy Alloy C276 Bars : 2mm to 6000mm

Tolerance of Hastelloy Alloy C276 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.01 max%

Manganese (Mn) : 1.00 max%

Enquiry Now
Hastelloy C2000

Hastelloy C2000

Thickness of Hastelloy Alloy C2000 Bars : 3mm Up to 600mm

Length of Hastelloy Alloy C2000 Bars : 2mm to 6000mm

Tolerance of Hastelloy Alloy C2000 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.01 max%

Silicon (Si) : 0.08 max%

Enquiry Now
Hastelloy C22

Hastelloy C22

Thickness of Hastelloy Alloy C22 Bars : 3mm Up to 600mm

Length of Hastelloy Alloy C22 Bars : 2mm to 6000mm

Tolerance of Hastelloy Alloy C22 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.015 max%

Manganese (Mn) : 0.50 max%

Enquiry Now
Hastelloy X

Hastelloy X

Thickness of Hastelloy Alloy X Bars : 3mm Up to 600mm

Length of Hastelloy Alloy X Bars : 2mm to 6000mm

Tolerance of Hastelloy Alloy X Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.05 - 0.15%

Manganese (Mn) : 1.00 max%

Enquiry Now
Hiperco 50

Hiperco 50

Thickness of Hiperco 50 Round Bars : 3mm Up to 600mm

Width of Hiperco 50 Round Bars : 2mm to 6000mm

Carbon(C) : 0.01%

Silicon(Si) : 0.05%

Iron(Fe) : 49%

Enquiry Now
Inconel 600

Inconel 600

At Harsh Steel Nickel Alloy 600 is available in Nickel Alloy 600 wire, Nickel 600 Round bar, Nickel 600 Forged bar, Nickel 600 hex bar, Nickel 600 Flat bar, Nickel 600 Circles, Nickel 600 Ring, Nickel 600 Tube, Nickel 600 seamless Pipe, Nickel 600 Welded / ERW Pipe, Nicke 600 Sheet, Nickel 600
Enquiry Now
Inconel 601

Inconel 601

At Harsh Steel Nickel Alloy 601 (UNS N06601) is available in Nickel Alloy 601 wire, Nickel Alloy 601 Round bar, Nickel Alloy 601 Forged bar, Nickel Alloy 601 hex bar, Nickel Alloy 601 Flat bar, Nickel Alloy 601 Circles, Nickel Alloy 601 Ring, Nickel Alloy 601 Tube, Nickel Alloy 601 seamless
Enquiry Now
Inconel 617

Inconel 617

At Harsh Steel Nickel Alloy 617 is available in Inconel 617 wire, Inconel 617 Round bar, Inconel 617 Forged bar, Inconel 617 hex bar, Inconel 617 Flat bar, Inconel 617 Circles, Inconel 617 Ring, Inconel 617 Tube, Inconel 617 seamless Pipe, Inconel 617 Welded / ERW Pipe, Inconel 617 Sheet, Inconel
Enquiry Now
Inconel 625

Inconel 625

Nickel Alloy-625 Bar : ASTM B 446, ASME SB 466, AMS 5666, ISO 9723, VdTUV 499, BS 3076 NA21, EN 10095, DIN 17752, ASME Code Case 1935

Nickel Alloy-625 Rod : ASTM B 446, ASME SB 466, ISO 9723, VdTUV 499, BS 3076 NA21, EN 10095, DIN 17752, SME Code Case 1935

Nickel Alloy-625 Wire : AMS 5837, ISO 9724, DIN 17753

Nickel Alloy-625 Forging Stock : ASTM B 564, ASME SB 564, AMS 5666, ISO 9725, SME Code Case 1935, DIN 17754

Nickel Alloy-625 Plate : ASTM B 443, ASME SB 443, AMS 5599, AMS 5869, MAM 5599, ISO 6208, VdTUV 499, BS 3072 NA21, EN 10095, DIN 17750, ASME Code Case 1935

Enquiry Now
Inconel 718

Inconel 718

At Harsh Steel Nickel 718 (UNS N07718) is available in Inconel 718 wire, Inconel 718 Round bar, Inconel 718 Forged bar, Inconel 718 hex bar, Inconel 718 Flat bar, Inconel 718 Circles, Inconel 718 Ring, Inconel 718 Tube, Inconel 718 Seamless Pipe, Inconel 718 Welded / ERW Pipe, Inconel 718 Sheet,
Enquiry Now
Inconel 738LC

Inconel 738LC

Thickness of Inconel Alloy 738/738lc Bars : 3mm Up to 738/738lcmm

Length of Inconel Alloy 738/738lc Bars : 2mm to 738/738lc0mm

Tolerance of Inconel Alloy 738/738lc Bars : h8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.15-0.20%

Manganese (Mn) : 0.20 max%

Enquiry Now
Inconel 800/H/HT

Inconel 800/H/HT

Incoloy Alloy 800 / 800H/ 800HT Rod : ASTM B 408, ASME SB 408, ISO 9723, BS 3076NA15, DIN 17460, EN 10095

Incoloy Alloy 800 / 800H/ 800HT Bar : AMS 5766, ASTM B 408, ASME SB 408, ISO 9723, BS 3076NA15, DIN 17460, EN 10095

Incoloy Alloy 800 / 800H/ 800HT Wire : ISO 9724, BS 3075NA15

Incoloy Alloy 800 / 800H/ 800HT Forgings : AMS 5766, ASTM B564, ASME SB 564, ASME Code Case 1949, ISO 9725, DIN 17460

Incoloy Alloy 800 / 800H/ 800HT Plate : AMS 5871, ASTM A 240/A 480, ASME SA 240/SA 480, ASTM B 409/B 906, ASME SB 409/SB 906, BS 3072NA15, DIN 17460, EN 10028-7, EN 10095

Enquiry Now
Inconel 825

Inconel 825

At Harsh Steel Nickel 825 is available in Incoloy 825 wire, Incoloy 825 Round bar, Incoloy 825 Forged bar, Incoloy 825 hex bar, Incoloy 825 Flat bar, Incoloy 825 Circles, Incoloy 825 Ring, Incoloy 825 Tube, Incoloy 825 seamless Pipe, Incoloy 825 Welded / ERW Pipe, Incoloy 825 Sheet, Incoloy 825
Enquiry Now
Inconel 901

Inconel 901

Solution Treatment : 1975-2025°F / 2 hrs + Air Cool

Stabilization Heat Treatment : 1425 - 1475°F / 2-4 hrs + Air Cool

Precipitation Heat Treatment : 1325 - 1375 / 24 hrs +Any Cool

Material : Nickel Alloy 901

Tensile Strength ksi : 150

Enquiry Now
Inconel X750

Inconel X750

Inconel X-750 Rod : ASTM B 637, ASME SB 637, ISO 9723, ISO9724, ISO9725, AMS 5667, AMS 5668, AMS 5669, AMS 5670, AMS 5671, AMS 5747, EN10269

Inconel X-750 Bar : ASTM B 637, ASME SB 637, ISO 9723, ISO9724, ISO9725, AMS 5667, AMS 5668, AMS 5669, AMS 5670, AMS 5671, AMS 5747, EN10269

Inconel X-750 Forging Stock : ASTM B 637, ASME SB 637, ISO 9723, ISO9724, ISO9725, AMS 5667, AMS 5668, AMS 5669, AMS 5670, AMS 5671, AMS 5747, EN10269

Inconel X-750 Plate : ISO 6208, AMS 5542 and AMS 5598

Inconel X-750 Sheet : ISO 6208, AMS 5542 and AMS 5598

Enquiry Now
Invar 36

Invar 36

Thickness of Invar 36 Bars : 3mm Up to 600mm

Length of Invar 36 Bars : 2mm to 6000mm

Tolerance of Invar 36 Bars : h8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.10 max%

Manganese (Mn) : 0.06 max%

Enquiry Now
Kovar

Kovar

Thickness of Kovar Bars : 3mm Up to 600mm

Length of Kovar Bars : 2mm to 6000mm

Tolerance of Kovar Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.04 max%

Manganese (Mn) : 0.50 max%

Enquiry Now
Maraging 250

Maraging 250

Alloy 250 (UNS K92890 / Maraging 250) is an age-hardenable iron-nickel steel. Alloy 250 combines ultra-high strength (1800MPa), good toughness, readily machinable in pre-aged condition, excellent transverse properties and resistance to crack propagation. C250 is used for missile and ejector
Enquiry Now
Maraging 300

Maraging 300

Maraging 300 is an age hardenable (maraging) iron nickel stainless steel. Maraging 300 has exceptional strength, toughness and is resistant to crack propagation. Maraging 300 is used for tooling, transmission shafts, autosport components and light aircraft landing gear. Specifications UNS
Enquiry Now
Maraging 350

Maraging 350

Material : Maraging 350

Yield Strength ksi 0.2 % : 330

Ultimate Tensile Strength ksi : 350

Elongation in 4D(%) : 8

Enquiry Now
Monel 400

Monel 400

Thickness of Monel Alloy 400 Bars : 3mm Up to 600mm

Length of Monel Alloy 400 Bars : 2mm to 6000mm

Tolerance of Monel Alloy 400 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.3 max%

Manganese (Mn) : 2.0 max%

Enquiry Now
Monel K500

Monel K500

Thickness of Alloy K500 Bars : 3mm Up to 600mm

Length of Alloy K500 Bars : 2mm to 6000mm

Tolerance of Alloy K500 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.25 max

Manganese (Mn) : 1.50 max

Enquiry Now
Mu Metal

Mu Metal

Specific Gravity : 8.7g/cm

Curie Temperature : 830°F (410°C)

Electrical Resistivity : 349 ohm circ mil/foot 0.55 ohm mm²m

Density lb/cu.in : 316

Thermal Conductivity : 134 btu-inch/ft hour °F 0.32 W/cm °C

Enquiry Now
Nickel 200

Nickel 200

Nickel Alloy-200 Rod : ASTM B 160, ASME SB 160, DIN 17752, ISO 9723

Nickel Alloy-200 Bar : ASTM B 160, ASME SB 160, DIN 17752, ISO 9723

Nickel Alloy-200 Pipe : ASTM B 161, ASME SB161, ASTM B 163, ASME SB 163, ASTM B 725, ASME SB 725, ASTM B 730, ASME SB 730, ASTM B 751, ASME B 751, ASTM B775, ASME SB 775, ASTM B 829, ASME SB 829 DIN 17751, ISO 6207

Nickel Alloy-200 Tube : ASTM B 161, ASME SB161, ASTM B 163, ASME SB 163, ASTM B 725, ASME SB 725, ASTM B 730, ASME SB 730, ASTM B 751, ASME B 751, ASTM B775, ASME SB 775, ASTM B 829, ASME SB 829 DIN 17751, ISO 6207

Nickel Alloy-200 Plate : ASTM B 162, ASME SB 162, DIN 17750, ISO 6208

Enquiry Now
Nickel 201

Nickel 201

Nickel Alloy-201 Rod : ASTM B 160, ASME SB 160, DIN 17752, ISO 9723

Nickel Alloy-201 Bar : ASTM B 160, ASME SB 160, DIN 17752, ISO 9723

Nickel Alloy-201 Pipe : ASTM B 161, ASME SB161, ASTM B 163, ASME SB 163, ASTM B 725, ASME SB 725, ASTM B 730, ASME SB 730, ASTM B 751, ASME B 751, ASTM B775, ASME SB 775, ASTM B 829, ASME SB 829 DIN 17751, ISO 6207

Nickel Alloy-201 Tube : ASTM B 161, ASME SB161, ASTM B 163, ASME SB 163, ASTM B 725, ASME SB 725, ASTM B 730, ASME SB 730, ASTM B 751, ASME B 751, ASTM B775, ASME SB 775, ASTM B 829, ASME SB 829 DIN 17751, ISO 6207

Nickel Alloy-201 Plate : ASTM B 162, ASME SB 162, DIN 17750, ISO 6208

Enquiry Now
Nimonic 263

Nimonic 263

At Harsh Steel Nickel 263 is available in Nimonic 263 wire, Nimonic 263 Round bar, Nimonic 263 Forged bar, Nimonic 263 hex bar, Nimonic 263 Flat bar, Nimonic 263 Circles, Nimonic 263 Ring, Nimonic 263 Tube, Nimonic 263 seamless Pipe, Nimonic 263 Welded / ERW Pipe, Nimonic 263 Sheet, Nimonic 263
Enquiry Now
Nimonic 75

Nimonic 75

Thickness of 75 Bars : 3mm Up to 600mm

Length of 75 Bars : 2mm to 6000mm

Tolerance of 75 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.08 - 0.15%

Manganese (Mn) : 1.00 max%

Enquiry Now
Nimonic 80A

Nimonic 80A

Material : Alloy 80A

Condition : Solution Annealed & Precipatation Treated (aged)

Ultimate Tensile Strength ksi : 145

Yield Strength ksi : 90

Elongation on 4D (min) : 20

Enquiry Now
Nimonic 90

Nimonic 90

Thickness of 90 bars : 3mm up to 600mm

Length of 90 bars : 2mm to 6000mm

Tolerance of 90 bars : h8, h9, h10, h11, k12, DIN 1013, A484, GRIT 240 & 320

Carbon (C) : 0.2 max

Manganese (Mn) : 1.00 max

Enquiry Now
Tantalum

Tantalum

Thickness of Tantalum Round Bars : 3mm Up to 600mm

Width of Tantalum Round Bars : 2mm to 6000mm

Tantalum(ta) : 99% Pure

Carbon(C) : 0.05% max

Sulfur(Co) : 0.025% max

Enquiry Now
Waspaloy

Waspaloy

Waspaloy is available in Waspaloy wire, Waspaloy Round bar, Waspaloy Forged bar, Waspaloy hex bar, Waspaloy Flat bar, Waspaloy Circles, Waspaloy Ring, Waspaloy Tube, Waspaloy seamless Pipe, Waspaloy Welded / ERW Pipe, Waspaloy Sheet, Waspaloy Plate, Waspaloy Coil, Waspaloy Flanges, Waspaloy
Enquiry Now

Titanium Alloys Products

Grade 1

Grade 1

Titanium Grade 1 is available in Bar, Billet, Extrusion, Plate, Sheet, Strip, Wire, Pipe, Tube, Rings and Forgings.Titanium Grades 1-4 are unalloyed and generally known as CP (Commercially Pure). The tensile and yield strength of titanium generally increases with the grade number. Titanium is 30%
Enquiry Now
Grade 2

Grade 2

Titanium Grade 2 is available in Bar, Billet, Extrusion, Plate, Sheet, Strip, Wire, Pipe, Tube, Rings and Forgings.Titanium Grades 1-4 are unalloyed and generally known as CP (Commercially Pure). The tensile and yield strength of titanium generally increases with the grade number. Titanium is 30%
Enquiry Now
Grade 3

Grade 3

Material : Titanium CP Grade 3, Annealed Sheet

Tensile Strength min ksi : 65

Tensile Strength min Mpa : 448

Yield Strength ksi : 55-80

Yield Strength MPa : 379-552

Enquiry Now
Grade 5

Grade 5

Thickness of Titanium Grade 5 Bars : 3mm Up to 600mm

Length of Titanium Grade 5 Bars : 2mm to 6000mm

Tolerance of Titanium Grade 5 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.08 max%

Titanium (Ti) : Balance%

Enquiry Now
Grade 6

Grade 6

Titanium Ti5Al2 5Sn is available in: Bar, Billet, Castings, Extrusion, Plate, Sheet, Wire. Titanium Ti5Al2.5Sn (Grade 6) is a high strength alloy which is most commonly used in airframe and jet engine applications. Titanium Ti5Al2.5Sn (Grade 6) has good weldability, stability and strength at
Enquiry Now
Grade 7

Grade 7

Thickness of Titanium Grade 7 Bars : 3mm Up to 600mm

Length of Titanium Grade 7 Bars : 2mm to 6000mm

Tolerance of Titanium Grade 7 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Carbon (C) : 0.10 max%

Titanium (Ti) : Balance%

Enquiry Now

Copper Nickel Alloys

Copper Nickel 70/30

Copper Nickel 70/30

Manganese (Mn) : 1.00%

Nickel (Ni) : 29.0-33.0%

Lead (Pb) : 0.05%

Copper (Cu) : 69.5%

Iron (Fe) : 0.40 - 1.00%

Enquiry Now
Copper Nickel 90/10

Copper Nickel 90/10

Thickness of Cupro Nickel 90-10 Bars : 3mm Up to 600mm

Length of Cupro Nickel 90-10 Bars : 2mm to 6000mm

Tolerance of Cupro Nickel 90-10 Bars : h8, h9, h10, h11, k12, DIN 1013, A484, GRIT 240 & 320

Manganese (Mn) : 1.00%

Nickel (Ni) : 9.0-11.0%

Enquiry Now

Aluminium Alloys Products

Aluminum Alloy 2014

Aluminum Alloy 2014

Thickness of Aluminium Alloy 2014 Bars : 3mm Up to 600mm

Length of Aluminium Alloy 2014 Bars : 2mm to 6000mm

Tolerance of Aluminium Alloy 2014 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Zinc (Zn) : 0.0 - 0.25%

Manganese (Mn) : 0.40 - 1.20%

Enquiry Now
Aluminum Alloy 2017

Aluminum Alloy 2017

Thickness of Aluminium Alloy 2017 Bars : 3mm Up to 600mm

Length of Aluminium Alloy 2017 Bars : 2mm to 6000mm

Tolerance of Aluminium Alloy 2017 Bars : H8, H9, H10, H11, K12, Din 1013, A484, Grit 240 & 320

Zinc (Zn) : 0.25 max%

Manganese (Mn) : 0.40 - 1.0%

Enquiry Now
Aluminum Alloy 5052

Aluminum Alloy 5052

Aluminum 5052 is one of the higher strength non-heat treatable alloys (Annealed it is stronger than 1100 and 3003). Alloy 5052 has excellent characteristics with a high fatigue strength it is used for structures which are subject to excessive vibrations. As 5052 also has excellent corrosion
Enquiry Now
Aluminum Alloy 5083

Aluminum Alloy 5083

Alloy 5083 is available in Plate, Sheet, Strip, Forging Stock, Tube and Bar. Alloy 5083 tube is available in many sizes from stock, however there is a minimum production of 30m.Specifications BS N8 Alcan GB-B54S Alcoa-505 BA
Enquiry Now
Aluminum Alloy 5154

Aluminum Alloy 5154

Alloy Designation : 5154

UK Specifications : BS N5 Alloy 5154A

Enquiry Now
Aluminum Alloy 6061

Aluminum Alloy 6061

Aluminium Alloy 6061 Sheet, Plate, Wire, Rod, Bar, Tube and extrusions. 6061 Foil (Shim) is available in various thicknessesAluminum 6061 is an extremely versatile heat treatable aluminum alloy. 6061 has a wide range of mechanical and corrosion resistance properties as well as having most of the
Enquiry Now
Aluminum Alloy 6063

Aluminum Alloy 6063

Alloy 6063 is available in Bar, Rod, Wire, Tube and Extrusions.Specifications AMS 4156 ASTM B221, ASTM B241, ASTM B491, ASTM B483, ASTM B210, ASTM B241, ASTM B345 And ASTM B429 MIL-P-25995 QQ-A-200/9 ASME SB221, ASME SB241 And ASME
Enquiry Now
Aluminum Alloy 6082

Aluminum Alloy 6082

Aluminum Alloy 6082 is available in Sheet and Plate, Aluminum 6082 Bar, 6082 is also available in Drawn Tube, Tube and Forging Stock.Alloy 6082 is a medium strength alloy with excellent corrosion resistance. Alloy 6082 has the highest strength of the 6000 series alloy. Due to the higher strength of
Enquiry Now
Aluminum Alloy 7050

Aluminum Alloy 7050

Color : Silver

Enquiry Now
Aluminum Alloy 7075

Aluminum Alloy 7075

Aluminium Alloy 7075 is available in Bar, Sheet, Plate, Strip, Forging Stock and Tube. View stock list for further information, Sheet Stock, PlateSpecifications BS 2 L95 Alloy 7075-T651 Plate BS 2 L88 Alloy 7075-T6 Clad Sheet and Strip BS L160 Alloy 7075-T73511 Bars and Sections BS L161 Alloy 7075
Enquiry Now

Duplex Steel Products

Duplex Steel S31803/32205

Duplex Steel S31803/32205

Duplex Steel S31803/32205 combines improved resistance to stress corrosion cracking, pitting, crevice corrosion and high strength. Due to it's chemical composition F51 duplex stainless steel resists chloride environments and sulphide stress corrosion. Availability Duplex Steel S31803/32205 is
Enquiry Now
Super Duplex Steel S32760

Super Duplex Steel S32760

Super Duplex Steel S32760 is the most common super duplex grade it has an enhanced pitting and crevice corrosion resistance compared with the ordinary austenitic or duplex types. AvailabilitySuper Duplex Steel S32760 is available in Bar from 6mm dia to 270mm dia and Forging Stock. For all stock
Enquiry Now

Fasteners

Bolts

Bolts

Size : 30-45mm, 45-60mm, 60-75mm, 75-90mm, 90-105mm

Material : Aluminium, Copper, Iron, Metal, Stainless Steel

Diameter : 20-30mm, 30-40mm, 50-60mm, 60-70mm, 70-80mm

Application : Automobiles, Automotive Industry, Fittings

Color : Silver

Enquiry Now
Washers

Washers

Size : 15-30mm, 30-45mm, 45-60mm

Type : Fastener Washers, Fittings Washers

Diameter : 20-30mm, 30-40mm, 40-50mm, 50-60mm, 60-70mm, 70-80mm

Shape : Rectangular, Round, Square

Thickness : 10-15mm

Enquiry Now

Speciality Products

Industrial Gasket

Industrial Gasket

Metal Gaskets : Ring Joint Gasket

Surface Finish : Electroplated

Color : Multi Colour

Material : Rubber

Thickness : 2.5-6.5 Mm

Enquiry Now
Instrumentation Manifolds

Instrumentation Manifolds

Design : Suitable for mounting on Rosemount, Yokogawa, Honeywell, ABB & other reputed Transmitters

Spindle Tip : Non–Rotating Tip: “Vee” Type & Ball Type (Tunsgten Carbide) Rotating Tip : “Vee” type only.

Seat : Metal to Metal, Stellited, Teflon

Packing & “O” Rings : Standard-PTFE. Optional GRAPHOIL, PEEK, CFT etc.

Patterns : “R” Type, “T” Type, “H” Type in standard & Co-Planar design.

Enquiry Now
$Refractory Anchor$

Refractory Anchor

Refractory Anchor

Form : Alloy Steel And Carbon Steel

Thickness : 2 To 12 Mm

Shapes : U Shapes, V Shapes And Y Shapes

Grades : 304, 310

Material : Steel

Enquiry Now
Stainless Steel Hoses

Stainless Steel Hoses

Application : Fertilizer Industries, Refineries Industries, Petrochemicals Industries, Chemical and Pharmaceuticals Industries.

Hose Material : AISI 321 (DIN EN 1.4541) / AISI 316L (DIN EN 1.4404)

Braid Material : AISI 304 (DIN EN 1.4301) / AISI 316L (DIN EN 1.4404)

Braid Type : Single Wire Braid

Inner Hose Size : 3/4" NB 1" NB 2" NB 2.1/2" NB 3" NB 4" NB 5" NB

Enquiry Now
Valves

Valves

Type : Valves

Automation Grade : Automatic, Manual

Size : 2” up to 56“ (DN 50 up to DN 1400)

Pressure Rating : ASME 150# to 2500#, API 3000PSI to 20000PSI

Materials : Carbon Steels, Austenitic Stainless Steels, Martensitic Steels, Duplex Stainless Steels, Super Duple

Enquiry Now
CNC Machined Components

CNC Machined Components

Finish : Polish

Material : Stainless Steel Alloy

Horse Power : 10.00-15.00

Thickness : 12 Mm

Technique : Hot Rolled

Enquiry Now

Raise your Query

Products